SPE Vacuum Manifolds

This standard vacuum manifold is recommended for starting solid-phase extraction. A 12 mm/16 mm Rack and waste liquid pump are provided as a set. InertSep Vacuum Manifold have an easy-to access structure to the next waste liquid funnel when performing solid phase extraction. Set Contents • Glass Chamber: 1 pc • Vacuum G...

For the efficient SPE analysis using InertSep vacuum manifold system, necessary accessories are provided as a kit for general or environmental analysis which needed many samples such as river water. Some kits are suitable for your analytical purposes. For General Analysis • InertSep vacuum manifold : 1 pc • Diaphragm Vacuum Pump : ...

For the efficient SPE analysis using InertSep vacuum manifold system, necessary accessories are provided as a kit for general or environmental analysis which needed many samples such as river water. Some kits are suitable for your analytical purposes. For Environmental Analysis • InertSep Vacuum Manifold System : 1 pc • Diaphragm V...

Nitric acid and sulfuric acid are used for inorganic compound analysis. This type of vacuum manifold system is made of stainless which have no concern of acid decay. This rack can set 50 mL DigiTUBEs up to 8 pcs. Set Contents • Glass chamber : 1 pc • Cover (for 8 samples) : 1 pc • Gasket : 1 pc • Vacuum Gauge (SUS) : 1 pc • ...

This is a set containing a rack for 50 mL eggplant-shaped flasks 4pc (100mL eggplant-shaped flasks 2 pcs). Set Contents • Glass Chamber : 1 pc • Cover: 1 pc • Gasket: 1 pc • Vacuum Gauge: 1 pc • Safety Valve: 1 pc • Plug: 4 pcs • PTFE Female Luer: 4 pcs • Stainless Delivery Tip: 4 pcs • GL-SPE Vacuum Manifold TS29/3...

GL-SPE Manifold Kit 20 is a vacuum manifold system for treatment of 20 pcs SPE cartridges at the same time. Racks for 20 mL and 30 mL concentration tubes and a vacuum controller is standardly attached to this kit. Set Contents • Glass Chamber : 1 pc • Gasket : 1 pc • Delivery Tip (SUS) : 20 pcs • Delivery Tip (PTFE) : 20 pcs ...

Flow controlled (approx. 1 mL/min) gravity flow elution speed enables to efficient elute of DNHP cartridges (up to 20 cartridges) after aldehyde capture. It is no need for pump to elute from cartridges, thus this system cut off manual troublesome elute procedure. Set Contents • Glass Chamber : 1 pc • 16 mm Test Tube Rack: 1 pc •...

Part for InertSep Manifold

Part for InertSep Manifold Fit onto the glass chamber to perform solid phase extraction.

Part for InertSep Manifold

Part for InertSep Manifold

Part for InertSep Manifold

Vacuum Manifold parts for Inorganic Compounds Analysis

Vacuum Manifold parts for Inorganic Compounds Analysis

Vacuum Manifold parts for Inorganic Compounds Analysis

Vacuum Manifold parts for Inorganic Compounds Analysis

Vacuum Manifold (for eggplant-shaped flasks) Parts

Vacuum Manifold (for eggplant-shaped flasks) Parts

Vacuum Manifold (for eggplant-shaped flasks) Parts

Vacuum Manifold 20(for 20 samples) Parts

Vacuum Manifold 20(for 20 samples) Parts

Vacuum Manifold 20(for 20 samples) Parts

Part for InertSep Manifold Display the level of vacuum in the glass chamber.

Part for InertSep Manifold Used to adjust the amount of vacuum applied. Adjust while monitoring the pressure displayed on the vacuum gauge

Part for InertSep Manifold A luer type connection can be made, e.g. with a solid phase cartridge or filter disk. Also used to connect the delivery tips to the cover.

Part for InertSep Manifold The standard delivery tip is manufactured. The standard delivery tip is manufactured from stainless steel (5010-50019). When correction resistance is required, use the PTFE type (5010-50020).

Part for InertSep Manifold The standard delivery tip is manufactured. The standard delivery tip is manufactured from stainless steel (5010-50019). When correction resistance is required, use the PTFE type (5010-50020).

Part for InertSep Manifold There 5 type of racks: 12/16 mm test tube, 20 mL concentration tube, 30 mL concentration tube, TS29/38 eggplant shaped flask, TS 29/38 Florence flask 50/100 mL.

Part for InertSep Manifold Used to connect the glass chamber to the vacuum pump.

Part for InertSep Manifold Need to plug any line not being used.

Part for InertSep Manifold Stainless steel nut for rack

Part for InertSep Manifold Resin nut for rack

Part for InertSep Manifold O-ring for rack

Part for InertSep Manifold Resin clip for rack

Vacuum Manifold 20 for InertSep mini AERO DNH Parts

Vacuum Manifold 20 for InertSep mini AERO DNH Parts

Vacuum Manifold 20 for InertSep mini AERO DNH Parts

Vacuum Manifold Vacuum Gauge for Non-Organic Analysis

Vacuum Manifold SUS Bleed Valve for Non-Organic Analysis

for 12C

for 12C Delivery tips are not included to the top plate.

for 12C

for 12C

for 96W